Proszę, dodaj wyjątek dla www.elektroda.pl do Adblock.
Dzięki temu, że oglądasz reklamy, wspierasz portal i użytkowników.

proFTPd ArchLinux problemy przy uruchomieniu

08 Lis 2009 18:04 1412 4
  • Poziom 9  
    Witam. Chcę postawić serwer FTP na Arch Linux.
    Pacmanem ściągnąłem proFTPd. Przy próbie uruchomienia wyskakuje taki komunikat:

    :: Starting ProFTPd Server [BUSY]
    - warning: unable to determine IP address of 'Server'
    - error: no valid servers configured
    - Fatal: error processing configuration file '/etc/proftpd.conf'

    uruchamiam go poleceniem /etc/rc.d/proftpd start

    Proszę o pomoc!!
  • Relpol
  • VIP Zasłużony dla elektroda
    Nie skonfigurowałeś serwera. W /etc masz przykładowy plik konfiguracyjny.
  • Relpol
  • Poziom 9  
    # This is a basic ProFTPD configuration file (rename it to
    # 'proftpd.conf' for actual use. It establishes a single server
    # and a single anonymous login. It assumes that you have a user/group
    # "nobody" and "ftp" for normal operation and anon.

    ServerName "Server"
    ServerType standalone
    DefaultServer on

    # Port 21 is the standard FTP port.
    Port 21

    # Don't use IPv6 support by default.
    UseIPv6 off

    # Umask 022 is a good standard umask to prevent new dirs and files
    # from being group and world writable.
    Umask 022

    # To prevent DoS attacks, set the maximum number of child processes
    # to 30. If you need to allow more than 30 concurrent connections
    # at once, simply increase this value. Note that this ONLY works
    # in standalone mode, in inetd mode you should use an inetd server
    # that allows you to limit maximum number of processes per service
    # (such as xinetd).
    MaxInstances 30

    # Set the user and group under which the server will run.
    User nobody
    Group nobody

    # To cause every FTP user to be "jailed" (chrooted) into their home
    # directory, uncomment this line.
    #DefaultRoot ~

    # Normally, we want files to be overwriteable.
    AllowOverwrite on

    # Bar use of SITE CHMOD by default
    <Limit SITE_CHMOD>

    # A basic anonymous configuration, no upload directories. If you do not
    # want anonymous users, simply delete this entire <Anonymous> section.
    <Anonymous ~ftp>
    User ftp
    Group ftp

    # We want clients to be able to login with "anonymous" as well as "ftp"
    UserAlias anonymous ftp

    # Limit the maximum number of anonymous logins
    MaxClients 10

    # We want 'welcome.msg' displayed at login, and '.message' displayed
    # in each newly chdired directory.
    DisplayLogin welcome.msg
    DisplayChdir .message

    # Limit WRITE everywhere in the anonymous chroot
    <Limit WRITE>

    TAK WYGLĄDA MÓJ CONFIG, co jest nieskonfigurowane?
  • VIP Zasłużony dla elektroda
    Przykładowa działająca konfiguracja:

    ServerName                      "evil"
    ServerType                      standalone
    DefaultServer                   on
    RequireValidShell               off
    AuthPAM                         off
    AuthPAMConfig                   ftp
    Port                            21
    Umask                           022
    MaxInstances                    30
    User                            proftpd
    Group                           proftpd
    <Directory />
            AllowOverwrite          on
    DefaultRoot ~
  • Poziom 9  
    dzięki udało mi się skonfigurować. ftp hula