smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-1607] (sf-6.6-1)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue Mobile
Device Model: WDC WD10SPCX-24HWST1
Serial Number: WD-WX21A85198ZL
LU WWN Device Id: 5 0014ee 606095193
Firmware Version: 02.01A02
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Aug 01 18:15:11 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 96 (intermediate level with standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (17160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 196) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 4188
3 Spin_Up_Time POS--K 188 184 021 - 1558
4 Start_Stop_Count -O--CK 096 096 000 - 4416
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate POSR-K 200 200 051 - 0
9 Power_On_Hours -O--CK 092 092 000 - 6521
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 098 098 000 - 2201
192 Power-Off_Retract_Count -O--CK 200 200 000 - 371
193 Load_Cycle_Count -O--CK 191 191 000 - 27265
194 Temperature_Celsius -O---K 111 095 000 - 36
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
240 Head_Flying_Hours -O--CK 092 092 000 - 6448
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 38 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 158 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 158 [13] occurred at disk power-on lifetime: 3607 hours (150 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6f 9c 27 10 40 00 Error: UNC at LBA = 0x6f9c2710 = 1872504592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 c8 00 00 6e f5 49 e0 40 00 00:19:02.454 READ FPDMA QUEUED
60 00 80 00 c0 00 00 6f f7 b7 70 40 00 00:19:02.440 READ FPDMA QUEUED
60 00 08 00 b8 00 00 6f 9c 27 10 40 00 00:19:02.437 READ FPDMA QUEUED
60 00 08 00 b0 00 00 6f 9c 27 08 40 00 00:19:02.437 READ FPDMA QUEUED
60 00 08 00 a8 00 00 6f 9c 27 00 40 00 00:19:02.437 READ FPDMA QUEUED
Error 157 [12] occurred at disk power-on lifetime: 3607 hours (150 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6f 9c 26 d0 40 00 Error: UNC at LBA = 0x6f9c26d0 = 1872504528
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 90 00 00 6e f5 4a 88 40 00 00:18:55.022 READ FPDMA QUEUED
60 00 08 00 88 00 00 6e f5 4a 80 40 00 00:18:55.020 READ FPDMA QUEUED
60 00 80 00 80 00 00 6f f7 b5 f0 40 00 00:18:55.020 READ FPDMA QUEUED
60 00 80 00 78 00 00 6f 9c 26 b8 40 00 00:18:55.019 READ FPDMA QUEUED
60 00 08 00 70 00 00 6e f5 4a 08 40 00 00:18:55.019 READ FPDMA QUEUED
Error 156 [11] occurred at disk power-on lifetime: 3605 hours (150 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 36 67 08 40 00 Error: WP at LBA = 0x00366708 = 3565320
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 28 00 10 00 00 00 63 bf 40 40 00 05:04:08.938 WRITE FPDMA QUEUED
61 00 08 00 08 00 00 05 f2 3a 78 40 00 05:04:08.938 WRITE FPDMA QUEUED
60 00 08 00 00 00 00 13 fc d9 58 40 00 05:04:08.937 READ FPDMA QUEUED
60 00 08 00 f8 00 00 07 c0 80 b0 40 00 05:04:08.937 READ FPDMA QUEUED
60 00 78 00 f0 00 00 00 36 66 a8 40 00 05:04:08.937 READ FPDMA QUEUED
Error 155 [10] occurred at disk power-on lifetime: 3605 hours (150 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 36 67 08 40 00 Error: WP at LBA = 0x00366708 = 3565320
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 30 00 00 00 63 bf 20 40 00 05:04:00.276 WRITE FPDMA QUEUED
60 00 80 00 28 00 00 00 36 66 a0 40 00 05:04:00.275 READ FPDMA QUEUED
61 00 08 00 20 00 00 00 67 c6 38 40 00 05:04:00.275 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 40 00 05:04:00.229 FLUSH CACHE EXT
61 00 c0 00 10 00 00 00 63 c4 30 40 00 05:03:57.543 WRITE FPDMA QUEUED
Error 154 [9] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 5e c1 a0 40 00 Error: UNC at LBA = 0x005ec1a0 = 6209952
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 30 00 d8 00 00 00 40 ce b0 40 00 03:37:50.758 READ FPDMA QUEUED
60 01 00 00 d0 00 00 00 5e df 78 40 00 03:37:50.758 READ FPDMA QUEUED
60 01 00 00 c8 00 00 00 5e de 78 40 00 03:37:50.758 READ FPDMA QUEUED
60 01 00 00 c0 00 00 00 5e dd 78 40 00 03:37:50.758 READ FPDMA QUEUED
60 01 00 00 b8 00 00 00 5e dc 78 40 00 03:37:50.758 READ FPDMA QUEUED
Error 153 [8] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 81 48 40 00 Error: UNC at LBA = 0x628c8148 = 1653375304
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 0d 00 58 00 00 00 09 52 20 40 00 03:27:53.097 READ FPDMA QUEUED
61 00 08 00 50 00 00 00 63 bf 50 40 00 03:27:53.097 WRITE FPDMA QUEUED
60 00 10 00 48 00 00 00 09 52 18 40 00 03:27:53.097 READ FPDMA QUEUED
60 00 08 00 40 00 00 62 8c 81 48 40 00 03:27:53.097 READ FPDMA QUEUED
60 00 40 00 38 00 00 44 96 01 e0 40 00 03:27:53.097 READ FPDMA QUEUED
Error 152 [7] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 81 40 40 00 Error: WP at LBA = 0x628c8140 = 1653375296
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 e8 00 00 62 c0 08 10 40 00 03:27:48.365 WRITE FPDMA QUEUED
61 00 08 00 e0 00 00 1e 4b 3e 38 40 00 03:27:48.365 WRITE FPDMA QUEUED
60 00 80 00 d8 00 00 13 ef c4 c8 40 00 03:27:48.364 READ FPDMA QUEUED
61 00 20 00 c8 00 00 44 c7 8a 40 40 00 03:27:48.364 WRITE FPDMA QUEUED
61 00 20 00 c0 00 00 44 c8 5b 20 40 00 03:27:48.364 WRITE FPDMA QUEUED
Error 151 [6] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 81 40 40 00 Error: UNC at LBA = 0x628c8140 = 1653375296
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 24 00 80 00 00 0e 45 23 58 40 00 03:27:43.913 READ FPDMA QUEUED
60 00 78 00 78 00 00 13 f1 aa 28 40 00 03:27:43.913 READ FPDMA QUEUED
60 00 38 00 70 00 00 11 3a 79 18 40 00 03:27:43.913 READ FPDMA QUEUED
60 00 40 00 68 00 00 12 1d b3 80 40 00 03:27:43.153 READ FPDMA QUEUED
60 00 78 00 60 00 00 08 b1 8f 50 40 00 03:27:43.151 READ FPDMA QUEUED
Error 150 [5] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 7e 20 40 00 Error: UNC at LBA = 0x628c7e20 = 1653374496
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 18 00 f0 00 00 00 2b a7 88 40 00 03:27:11.502 READ FPDMA QUEUED
60 00 08 00 e8 00 00 62 8c 7e 20 40 00 03:27:11.502 READ FPDMA QUEUED
61 00 d0 00 e0 00 00 0b 18 47 90 40 00 03:27:11.502 WRITE FPDMA QUEUED
61 01 00 00 d8 00 00 0b 18 46 90 40 00 03:27:11.484 WRITE FPDMA QUEUED
61 01 00 00 c8 00 00 0b 18 45 90 40 00 03:27:11.484 WRITE FPDMA QUEUED
Error 149 [4] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 7e 18 40 00 Error: UNC at LBA = 0x628c7e18 = 1653374488
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 03 00 40 00 00 01 cf 0f 30 40 00 03:27:07.423 READ FPDMA QUEUED
60 00 38 00 38 00 00 00 2b a6 40 40 00 03:27:07.423 READ FPDMA QUEUED
60 00 08 00 30 00 00 62 8c 7e 18 40 00 03:27:07.368 READ FPDMA QUEUED
60 00 03 00 28 00 00 01 5d d3 c0 40 00 03:27:07.367 READ FPDMA QUEUED
2f 00 00 00 01 00 00 00 00 00 10 68 00 03:27:07.347 READ LOG EXT
Error 148 [3] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 7e 18 40 00 Error: UNC at LBA = 0x628c7e18 = 1653374488
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 38 00 20 00 00 00 2b a6 a0 40 00 03:27:01.609 READ FPDMA QUEUED
60 00 18 00 10 00 00 09 a8 2a e8 40 00 03:27:01.538 READ FPDMA QUEUED
60 00 08 00 f8 00 00 09 a8 2a b8 40 00 03:27:01.538 READ FPDMA QUEUED
61 00 08 00 f0 00 00 0a b9 e2 28 40 00 03:27:01.530 WRITE FPDMA QUEUED
61 00 18 00 e8 00 00 0a b9 e1 f8 40 00 03:27:01.528 WRITE FPDMA QUEUED
Error 147 [2] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 69 a0 40 00 Error: UNC at LBA = 0x628c69a0 = 1653369248
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 b0 00 00 62 8c 69 a0 40 00 03:26:41.801 READ FPDMA QUEUED
61 00 08 00 a8 00 00 00 43 b0 70 40 00 03:26:41.801 WRITE FPDMA QUEUED
61 00 08 00 a0 00 00 00 ef a8 10 40 00 03:26:41.777 WRITE FPDMA QUEUED
60 00 10 00 98 00 00 11 4d c6 78 40 00 03:26:41.777 READ FPDMA QUEUED
60 00 38 00 90 00 00 00 54 72 50 40 00 03:26:41.777 READ FPDMA QUEUED
Error 146 [1] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 69 90 40 00 Error: UNC at LBA = 0x628c6990 = 1653369232
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 38 00 68 00 00 00 10 cb b8 40 00 03:26:35.328 READ FPDMA QUEUED
60 00 80 00 60 00 00 0a ef 6c b0 40 00 03:26:35.328 READ FPDMA QUEUED
61 00 3d 00 58 00 00 00 94 d8 e4 40 00 03:26:35.311 WRITE FPDMA QUEUED
61 00 08 00 50 00 00 00 63 bf 30 40 00 03:26:35.251 WRITE FPDMA QUEUED
60 00 38 00 48 00 00 00 56 8c f0 40 00 03:26:35.251 READ FPDMA QUEUED
Error 145 [0] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 69 90 40 00 Error: WP at LBA = 0x628c6990 = 1653369232
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 01 00 00 e0 00 00 01 eb 31 28 40 00 03:26:31.323 WRITE FPDMA QUEUED
61 01 00 00 d8 00 00 01 eb 30 28 40 00 03:26:31.322 WRITE FPDMA QUEUED
61 01 00 00 c8 00 00 01 eb 2f 28 40 00 03:26:31.322 WRITE FPDMA QUEUED
61 01 00 00 90 00 00 01 eb 2e 28 40 00 03:26:31.321 WRITE FPDMA QUEUED
61 01 00 00 88 00 00 01 eb 2d 28 40 00 03:26:31.321 WRITE FPDMA QUEUED
Error 144 [23] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 69 88 40 00 Error: WP at LBA = 0x628c6988 = 1653369224
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 01 00 00 80 00 00 12 79 2c d0 40 00 03:26:26.501 WRITE FPDMA QUEUED
61 01 00 00 28 00 00 12 79 2b d0 40 00 03:26:26.500 WRITE FPDMA QUEUED
61 01 00 00 10 00 00 12 79 2a d0 40 00 03:26:26.408 WRITE FPDMA QUEUED
61 01 00 00 08 00 00 12 79 29 d0 40 00 03:26:26.408 WRITE FPDMA QUEUED
61 01 00 00 00 00 00 12 79 28 d0 40 00 03:26:26.407 WRITE FPDMA QUEUED
Error 143 [22] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 8c 69 88 40 00 Error: UNC at LBA = 0x628c6988 = 1653369224
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 a8 00 00 09 35 0a e0 40 00 03:26:21.809 READ FPDMA QUEUED
60 01 00 00 98 00 00 09 35 09 e0 40 00 03:26:21.808 READ FPDMA QUEUED
60 01 00 00 90 00 00 09 35 08 e0 40 00 03:26:21.807 READ FPDMA QUEUED
60 01 00 00 80 00 00 09 35 07 e0 40 00 03:26:21.806 READ FPDMA QUEUED
60 01 00 00 58 00 00 09 35 06 e0 40 00 03:26:21.805 READ FPDMA QUEUED
Error 142 [21] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 71 bf 72 a8 40 00 Error: UNC at LBA = 0x71bf72a8 = 1908372136
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 80 00 00 09 82 7e 98 40 00 03:26:05.664 READ FPDMA QUEUED
60 01 00 00 78 00 00 09 82 7d 98 40 00 03:26:05.664 READ FPDMA QUEUED
60 01 00 00 70 00 00 09 82 7c 98 40 00 03:26:05.663 READ FPDMA QUEUED
60 01 00 00 68 00 00 09 82 7b 98 40 00 03:26:05.662 READ FPDMA QUEUED
60 01 00 00 60 00 00 09 82 7a 98 40 00 03:26:05.659 READ FPDMA QUEUED
Error 141 [20] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 71 bf 72 a8 40 00 Error: UNC at LBA = 0x71bf72a8 = 1908372136
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 80 00 18 00 00 08 8f 7a c0 40 00 03:26:01.370 READ FPDMA QUEUED
60 00 80 00 10 00 00 07 c1 f6 88 40 00 03:26:01.352 READ FPDMA QUEUED
60 00 08 00 08 00 00 08 8f 7f b0 40 00 03:26:01.351 READ FPDMA QUEUED
60 00 50 00 00 00 00 08 8f 7f 98 40 00 03:26:01.350 READ FPDMA QUEUED
60 00 18 00 f8 00 00 00 4c 60 48 40 00 03:26:01.350 READ FPDMA QUEUED
Error 140 [19] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 0e 9f d0 40 00 Error: UNC at LBA = 0x000e9fd0 = 958416
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 80 00 70 00 00 06 21 10 e8 40 00 03:25:26.776 READ FPDMA QUEUED
60 00 80 00 68 00 00 06 f6 18 90 40 00 03:25:26.776 READ FPDMA QUEUED
61 00 18 00 60 00 00 00 63 bf 30 40 00 03:25:26.776 WRITE FPDMA QUEUED
60 00 07 00 58 00 00 00 0e a0 08 40 00 03:25:26.776 READ FPDMA QUEUED
60 00 07 00 50 00 00 00 0e a0 08 40 00 03:25:26.776 READ FPDMA QUEUED
Error 139 [18] occurred at disk power-on lifetime: 3604 hours (150 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 4c 61 10 40 00 Error: WP at LBA = 0x004c6110 = 5005584
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 08 00 b8 00 00 00 63 bf b0 40 00 03:25:02.821 WRITE FPDMA QUEUED
61 00 78 00 b0 00 00 00 65 77 28 40 00 03:25:02.820 WRITE FPDMA QUEUED
61 01 00 00 a8 00 00 00 65 76 28 40 00 03:25:02.820 WRITE FPDMA QUEUED
61 00 08 00 a0 00 00 00 5d 55 40 40 00 03:25:02.820 WRITE FPDMA QUEUED
60 00 10 00 98 00 00 09 54 1e d8 40 00 03:25:02.816 READ FPDMA QUEUED
Error 138 [17] occurred at disk power-on lifetime: 3603 hours (150 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 62 c0 19 58 40 00 Error: UNC at LBA = 0x62c01958 = 1656756568
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 b0 00 00 62 c0 19 58 40 00 02:40:18.848 READ FPDMA QUEUED
60 00 08 00 a8 00 00 64 fc e9 88 40 00 02:40:18.799 READ FPDMA QUEUED
60 00 08 00 a0 00 00 64 fc e6 c0 40 00 02:40:18.766 READ FPDMA QUEUED
60 00 50 00 98 00 00 11 7e 15 38 40 00 02:40:18.751 READ FPDMA QUEUED
60 00 10 00 90 00 00 00 09 1e d8 40 00 02:40:18.740 READ FPDMA QUEUED
Error 137 [16] occurred at disk power-on lifetime: 3601 hours (150 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 21 ea 10 40 00 Error: UNC at LBA = 0x0021ea10 = 2222608
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 28 00 38 00 00 00 a0 65 60 40 00 00:40:41.068 READ FPDMA QUEUED
60 00 08 00 30 00 00 11 42 33 a0 40 00 00:40:41.068 READ FPDMA QUEUED
60 00 c8 00 28 00 00 00 21 ea 78 40 00 00:40:41.067 READ FPDMA QUEUED
60 01 00 00 20 00 00 00 21 e9 78 40 00 00:40:41.067 READ FPDMA QUEUED
60 01 00 00 18 00 00 00 21 e8 78 40 00 00:40:41.067 READ FPDMA QUEUED
Error 136 [15] occurred at disk power-on lifetime: 3601 hours (150 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 00 37 43 40 40 00 Error: UNC at LBA = 0x00374340 = 3621696
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 e8 00 00 09 a9 d6 00 40 00 00:39:22.708 READ FPDMA QUEUED
60 00 18 00 e0 00 00 00 37 43 36 40 00 00:39:22.694 READ FPDMA QUEUED
60 00 08 00 d8 00 00 12 86 5c 20 40 00 00:39:22.678 READ FPDMA QUEUED
60 00 40 00 d0 00 00 08 11 e3 40 40 00 00:39:22.649 READ FPDMA QUEUED
60 00 08 00 c8 00 00 11 6f e9 f0 40 00 00:39:22.638 READ FPDMA QUEUED
Error 135 [14] occurred at disk power-on lifetime: 3599 hours (149 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 95 08 00 40 00 Error: UNC at LBA = 0x6e950800 = 1855260672
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 01 00 c8 00 00 6e 95 08 00 40 00 01:05:32.404 READ FPDMA QUEUED
61 00 c0 00 c0 00 00 00 64 55 20 40 00 01:05:32.404 WRITE FPDMA QUEUED
61 00 08 00 b8 00 00 05 c6 40 50 40 00 01:05:32.403 WRITE FPDMA QUEUED
61 00 08 00 b0 00 00 12 92 1d 78 40 00 01:05:32.403 WRITE FPDMA QUEUED
60 00 20 00 a8 00 00 00 00 00 02 40 00 01:05:32.403 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor (0x50) Completed without error 00% 524 -
# 2 Short offline Completed without error 00% 524 -
# 3 Vendor (0x50) Completed without error 00% 327 -
# 4 Short offline Completed without error 00% 327 -
# 5 Short offline Aborted by host 10% 193 -
# 6 Vendor (0x50) Aborted by host 80% 24 -
# 7 Short offline Completed without error 00% 24 -
# 8 Vendor (0x50) Completed without error 00% 7 -
# 9 Short offline Completed without error 00% 7 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Stand-by (1)
Current Temperature: 36 Celsius
Power Cycle Min/Max Temperature: 36/50 Celsius
Lifetime Min/Max Temperature: 6/53 Celsius
Lifetime Average Temperature: 34 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 128 (96)
Index Estimated Time Temperature Celsius
97 2018-08-01 16:08 49 ******************************
... ..( 41 skipped). .. ******************************
11 2018-08-01 16:50 49 ******************************
12 2018-08-01 16:51 48 *****************************
13 2018-08-01 16:52 49 ******************************
... ..( 2 skipped). .. ******************************
16 2018-08-01 16:55 49 ******************************
17 2018-08-01 16:56 48 *****************************
18 2018-08-01 16:57 49 ******************************
19 2018-08-01 16:58 49 ******************************
20 2018-08-01 16:59 49 ******************************
21 2018-08-01 17:00 48 *****************************
22 2018-08-01 17:01 49 ******************************
23 2018-08-01 17:02 49 ******************************
24 2018-08-01 17:03 49 ******************************
25 2018-08-01 17:04 48 *****************************
26 2018-08-01 17:05 49 ******************************
27 2018-08-01 17:06 49 ******************************
28 2018-08-01 17:07 48 *****************************
... ..( 6 skipped). .. *****************************
35 2018-08-01 17:14 48 *****************************
36 2018-08-01 17:15 49 ******************************
37 2018-08-01 17:16 48 *****************************
... ..( 48 skipped). .. *****************************
86 2018-08-01 18:05 48 *****************************
87 2018-08-01 18:06 45 **************************
88 2018-08-01 18:07 44 *************************
89 2018-08-01 18:08 42 ***********************
90 2018-08-01 18:09 41 **********************
91 2018-08-01 18:10 40 *********************
92 2018-08-01 18:11 39 ********************
93 2018-08-01 18:12 38 *******************
94 2018-08-01 18:13 38 *******************
95 2018-08-01 18:14 37 ******************
96 2018-08-01 18:15 37 ******************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 12404 Vendor specific
$2 za prototyp PCBs
, a tu nagle sie zawiesił i "piszczał" jak powiedział ojciec (nie było mnie przy tym) , ojciec wygiągnał baterie , a przy ponownym włączeniu wyświetla sie komunikat : Reboot and Select proper Boot Device ..... itd , w biosie wszystko Ok (zresztą resetowałem go) , dysk niby śmiga , ale nie czyta go ;/ i cały czas wyskakuje ten komunikat , miał ktoś może podobny przypadek ? jesli tak to proszę o jakieś info 
, a tu nagle sie zawiesił i "piszczał" jak powiedział ojciec (nie było mnie przy tym) , ojciec wygiągnał baterie , a przy ponownym włączeniu wyświetla sie komunikat : Reboot and Select proper Boot Device ..... itd , w biosie wszystko Ok (zresztą resetowałem go) , dysk niby śmiga , ale nie czyta go ;/ i cały czas wyskakuje ten komunikat , miał ktoś może podobny przypadek ? jesli tak to proszę o jakieś info 
z góry Dzieki !