Elektroda.pl
Elektroda.pl
X

Search our partners

Find the latest content on electronic components. Datasheets.com
Please add exception to AdBlock for elektroda.pl.
If you watch the ads, you support portal and users.

nokia 2730c-1 - cyclone box

darioosh 06 Sep 2012 15:03 1704 2
  • #1
    darioosh
    Level 14  
    Witam, robiąc update firmware przez USB telefon po restarcie już się nie obudził. Podłanczając telefon jest tylko komunikat "nie rozpoznano urządzenia usb". Cyclone box reloaded wyświetla tak:



    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101023000
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 2480010DF3018E56580ACC190663EBA53F36CE93
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
    CMT_BOOT_ROM_CRC: 273F6D55
    CMT_SECURE_ROM_CRC: DFAAF68F
    CMT Ready!
    Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
    RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using OLD BB5 FLASHING PROTOCOL
    If software STUCK HERE with box TX LED lit, that means:
    1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
    2. Your cable is not TX2 Enabled!
    3. Transmission error occured, try again
    In either cases, you need to reconnect your box from USB.
    FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR
    FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
    Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
    FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V
    RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
    Flashbus Write baud set to 2.0Mbits
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Box VPP disabled
    Internal CMT Phone VPP Enabled
    Warning: PAPUBKEYS Hash Missing!
    APE Boot skipped on user request
    Flashbus Write baud set to 5.0Mbits
    Restarting MCU...

    Podpowie ktoś z kolegów co może być?
    Dodam że wogóle nie można uruchomić telefonu w local mode.
  • #2
    ZAHYR
    Level 32  
    Próbuj flashować najwyższą wersją po FBUSie.
  • #3
    darioosh
    Level 14  
    Przy próbie flashowania jest tak:

    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101023000
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 2480010DF3018E56580ACC190663EBA53F36CE93
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
    CMT_BOOT_ROM_CRC: 273F6D55
    CMT_SECURE_ROM_CRC: DFAAF68F
    CMT Ready!
    rm578__10.47.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
    Searching for BootCode: DualLine 32Bit
    RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using OLD BB5 FLASHING PROTOCOL
    If software STUCK HERE with box TX LED lit, that means:
    1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
    2. Your cable is not TX2 Enabled!
    3. Transmission error occured, try again
    In either cases, you need to reconnect your box from USB.
    FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR
    FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
    Searching for BootCode: DualLine 32Bit
    FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V
    RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
    Flashbus Write baud set to 2.0Mbits
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    Internal Box VPP Enabled
    External CMT Phone VPP Enabled, Source: Box Internal 5V
    Warning: PAPUBKEYS Hash Missing!
    Flashbus Write baud set to 5.0Mbits
    Sending Certificates...
    Certificates OK
    Started group flash erase
    EraseArea[0,CMT]: 0x00000000-0x000006BF, NOR
    EraseArea[0,CMT]: 0x000006C0-0x0001FFFF, NOR
    EraseArea[0,CMT]: 0x00040000-0x000BFFFF, NOR
    EraseArea[0,CMT]: 0x000C0000-0x0013FFFF, NOR
    EraseArea[0,CMT]: 0x00140000-0x0155FFFF, NOR
    EraseArea[0,CMT]: 0x01560000-0x0175FFFF, NOR
    Waiting 320s for erasure finish...
    Erase taken 0.234s
    Writing all blocks...
    Initializing TurboCache...
    TurboCache Loaded!
    Writing CMT NOLO Certificate...
    Block Write Failed -> Failed to write CMT cert data (3), Programming Status Error
    Processing Flash Image Failed -> Failed to write all blocks
    Failed to Process all Image files -> Failed to process rm578__10.47.mcusw