Elektroda.pl
Elektroda.pl
X
Proszę, dodaj wyjątek dla www.elektroda.pl do Adblock.
Dzięki temu, że oglądasz reklamy, wspierasz portal i użytkowników.

Nokia 6303ci - nie można zrobić flasha

28 Cze 2013 09:55 2319 6
  • Poziom 10  
    witam,
    Wpadły mi dzisiaj dwie 6303ci jedna do aktualizacji druga do polaka. Obie zachowują się identycznie, w trakcie flasha po usb infinity-boxem po kilku procentach proces się zatrzymuje. I teraz nie do ruszenia niczym. Wszystkie boxy na usb mają tą samą reakcje po kilku procentach proces się zatrzymuje (mt-box, infinity, mx-key) na kopycie mx-box na 10pin w ogóle nie startuje, na hwk, infinity i mx-key startuje ale się wykrzacza. Próbowałem na kliku różnych softach, obie po kilkunastu próbach. Obie sztuki sprawdzone przed podpięciem, były sprawne i miały dużo niższe softy. Może ktoś ma jakiś pomysł bo mi już sił brak :(

    Przesyłam przykładowe logi:

    Infinity-Box
    F-BUS


    Selected FlashSettings : Manual
    Files Set for Flashing :
    MCU : rm638__10.80.mcusw
    PPM : rm638__10.80.ppm_b
    CNT : rm638__10.80.image_b_0594085_010
    FlashFile verify disabled
    -> SWversion check skipped : Dead mode selected

    Backup enabled, Will read Certificates now...
    Setting FlashMode
    FlashMode set Ok

    1st boot Ok, C0

    CMT part info :
    CMT ASICID : 000000010000022600000001020C192102054100
    CMT EM0 ID : 00001040
    CMT EM1 ID : 00001030
    CMT PUB ID : 177000078217004922D185B7DC5FBF5AD48BD299
    CMT MODE ID : 00
    CMT R_HASH : 7B045400E1752022F9EB80B0DEA9C65D
    CMT ROM ID : 67E82268F29CEA60

    CMT : Sending 2nd loader...
    Use : RAP3Gv4_2nd.fg , Rev : 0.0 Ver : 1.42.0
    Error : 2nd boot not accepted
    RX : F372C007011500000000


    Init Service mode... Wait...

    Init Service Mode Failed!
    Certificate read error, try continue flashing...
    Setting FlashMode
    FlashMode set Ok

    1st boot Ok, C0

    CMT part info :
    CMT ASICID : 000000010000022600000001020C192102054100
    CMT EM0 ID : 00001040
    CMT EM1 ID : 00001030
    CMT PUB ID : 177000078217004922D185B7DC5FBF5AD48BD299
    CMT MODE ID : 00
    CMT R_HASH : 7B045400E1752022F9EB80B0DEA9C65D
    CMT ROM ID : 67E82268F29CEA60

    CMT : Sending 2nd loader...
    Use : RAP3Gv4_2nd.fg , Rev : 0.0 Ver : 1.42.0
    CMT Loader sent, Boot Ok
    MCU Configuration
    MCU Cfg Ok , FF
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )
    ERR : UNK : FF ( Damaged HW? )

    Error on prepare stage - connection fail or HW error

    Connect phone on selected interface...

    Connect phone on selected interface...

    UFS S/N 65131 boot - Ok


    PO USB

    Selected FlashSettings : Manual
    FlashFile verify disabled

    Files Set for Flashing :
    MCU : rm638__10.80.mcusw
    PPM : rm638__10.80.ppm_b
    CNT : rm638__10.80.image_b_0594085_010
    Flashing phone now...
    Check files done...
    -> SWversion check skipped : Dead mode selected
    Dead Mode is Selected
    Waiting for USB device...
    --- Insert cable and charger or press phone's power button! ---
    -> Phone not found.. :(
    -> Boot fail...
    Flashing failed...

    Core : v1.52 , FlashEngine : v1.8

    Selected FlashSettings : Manual
    FlashFile verify disabled

    Files Set for Flashing :
    MCU : rm638__10.80.mcusw
    PPM : rm638__10.80.ppm_b
    CNT : rm638__10.80.image_b_0594085_010
    Flashing phone now...
    Check files done...
    -> SWversion check skipped : Dead mode selected
    Dead Mode is Selected
    Waiting for USB device...
    --- Insert cable and charger or press phone's power button! ---
    Connection opened successfully
    Waiting for communication response...
    BootRom : 1st boot ok
    ASIC ID: 000000010000022600000001020C192102054100
    CPU ID : RAP3Gv4 , Features : Dead-Test , USBRPL , FullUSB
    EM0 ID: 00001040
    EM1 ID: 00001030
    PUBLIC ID: 177000078217004922D185B7DC5FBF5AD48BD299
    ASIC MODE ID: 00
    ROOT KEY HASH: 7B045400E1752022F9EB80B0DEA9C65D
    ROM ID: 67E82268F29CEA60
    Use RAP3Gv40_2nd.fg , Rev : 3.0 Ver : 12.8.0
    Processing RAWLOADER...
    FLIC : 003000EC
    Req : XSR 1.6
    Use RAP3Gv40_XSR17_alg.fg , Rev : 3.0 Ver : 12.8.0
    Processing PASUBTOC ...
    Processing ALG ...
    Boot Done! :)
    TIME : Boot time : 00:00:02
    Reopening the connection...
    Waiting for response: 30
    Waiting for response: 29
    ADL: Check mode
    Select ASIC [C900]
    PAPUBkeys : 108AF4DB7EC8B1B36E9D6A60F7EB2996DC7B2B5D
    ADL: phone is in flash mode

    Backup enabled, will read all certificates...
    Reading NPC certificate...
    IMEI : 353402044645050
    Reading CCC certificate...
    Reading HWC certificate...
    Reading R&D certificate...
    Reading VARIANT certificate...
    Reading PARTNERC certificate...
    Reading MDM_KEYS certificate...
    Cert Read done!

    NPC Certificate saved...
    CCC Certificate saved...
    HWC Certificate saved...

    RPL saved : c:\InfinityBox\BEST\Backup\Cert\353402044645050_CRT.rpl

    ===Flashing [MCU]===
    Erase : Processing rm638__10.80.mcusw
    Partitioning....
    Partitioning Ok...
    Erasing....
    Erasing Ok...
    TIME : Erase time : 00:00:00
    Write : Processing rm638__10.80.mcusw
    CMT: Writing Hash CERT [ADA]
    CMT: Writing Hash CERT [KEYS]
    CMT: Writing Hash CERT [PRIMAPP]
    CMT: Writing Hash CERT [PASUBTOC]
    CMT: Writing Hash CERT [PAPUBKEYS]
    CMT: Writing Hash CERT [RAP3NAND]
    CMT: Writing Hash CERT [UPDAPP]
    Write error : Connection lost => HW error or Cable problem...
    Write CMT failed on block 13 :(

    Connect phone on selected interface...


    MX-Key
    F-BUS


    Connection status: OHCI:HUB:USB 2.00 (Full-speed)
    Driver: WinUSB, ver: 3.5.0.0
    Module ver: 1.0.0.21313(12-12-2012), Library ver: 1.0.0.14337(12-12-2012)
    CMT Data :
    SYSTEM ASIC ID: 000000010000022600000001020C192102054100 [RAPS2 ver: PA 4.x]
    EM0 ID: 00001040
    EM1 ID: 00001030
    PUBLIC ID: 22D00003444A00495BA41B7099131B07E44ED22C
    ASIC MODE ID: 00
    ROOT KEY HASH: 7B045400E1752022F9EB80B0DEA9C65D
    ROM ID: 67E82268F29CEA60
    SecondaryBoot: RAP3Gv40_2nd.fg [BB5] version: 12.8.0 revision: 3.0 size: 0x3AC0
    Supported Ids: 0203192102004000, 020C192102004000, 0203192102024000, 020C192102024000, 020C192102004100, 0203192102004100, 020C192102014100, 0203192102014100, 020C192102014000, 0203192102014000, 020C192102034000, 0203192102034000, 0203192102024100, 020C192102024100, 0203192102034100, 020C192102034100, 0203192102054100, 020C192102054100, 0203192102044100, 020C192102044100
    eBB5ProtocolType: NEW
    TransmissionMode: DDR&TX2
    Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
    Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
    Storage2: 0000 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
    Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
    Storage4: 00EC 0030 - 0000 0321 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
    Suggested algorithm: XSR 1.6
    Algorithm: RAP3Gv40_XSR17_alg.fg [XSR 1.6] version: 12.8.0 revision: 3.0 size: 0x9AE03
    Supported Ids: 0203192102004000, 020C192102004000, 0203192102024000, 020C192102024000, 020C192102004100, 0203192102004100, 020C192102014100, 0203192102014100, 020C192102014000, 0203192102014000, 020C192102034000, 0203192102034000, 0203192102024100, 020C192102024100, 0203192102034100, 020C192102034100, 0203192102054100, 020C192102054100, 0203192102044100, 020C192102044100
    TransmissionMode: DDR&TX2
    FUR: Adding Asic CMT as client OK
    CMT PAPUBKEYS HASH: 108AF4DB7EC8B1B36E9D6A60F7EB2996DC7B2B5D
    Processing MCU file: rm638__10.80.mcusw
    [BB5,XSR 1.6] size: 26.53 MB
    Supported Ids: 020C192102034000, 0203192102034000, 020C192102034100, 0203192102034100, 0203192102054100, 020C192102054100
    Storing certificate [NPC, CCC, HWC, R&D] ...ERROR: Packet Error(0xAA), code 0xA4000002
    Error
    Erase size: 37.69 MB
    CMT FLASH,MuxOneNAND area [00020000-000203FF]
    CMT FLASH,MuxOneNAND area [00060000-0009FFFF]
    CMT FLASH,MuxOneNAND area [000A0000-0025FFFF]
    CMT FLASH,MuxOneNAND area [003E0000-005DFFFF]
    CMT FLASH,MuxOneNAND area [005E0000-010DFFFF]
    CMT FLASH,MuxOneNAND area [01EC0000-01EDFFFF]
    CMT FLASH,MuxOneNAND area [027C0000-02CBFFFF]
    CMT FLASH,MuxOneNAND area [077C0000-07B3FFFF]
    CMT FLASH,MuxOneNAND area [010E0000-01EBFFFF]
    Error while erasing, Result: 00000000000000 , 0

    USB

    Connection status: OHCI:HUB::USB 2.00 (Full-speed)
    Driver: NMWCD, ver: 7.1.32.75
    Module ver: 1.0.0.21313(12-12-2012), Library ver: 1.0.0.14337(12-12-2012)
    Processing MCU file: rm638__10.80.mcusw
    [BB5,XSR 1.6] size: 26.53 MB
    Supported Ids: 020C192102034000, 0203192102034000, 020C192102034100, 0203192102034100, 0203192102054100, 020C192102054100
    Make sure USB cable, Battery and charger are removed from device.
    Insert USB cable, Battery back to device(make sure to have fully charged battery).
    Insert Charger or Press phone's power button(if flashing doesnt start automatically)
    Waiting for USB ROM device ...
    CMT SYSTEM ASIC ID: 000000010000022600000001020C192102054100 [RAPS2 ver: PA 4.x]
    CMT EM0 ID: 00001040
    CMT EM1 ID: 00001030
    CMT PUBLIC ID: 177000078217004922D185B7DC5FBF5AD48BD299
    CMT ASIC MODE ID: 00
    CMT ROOT KEY HASH: 7B045400E1752022F9EB80B0DEA9C65D
    CMT ROM ID: 67E82268F29CEA60
    Loading CMT secondary boot code
    SecondaryBoot: RAP3Gv40_2nd.fg [BB5] version: 11.14.0 revision: 3.0 size: 0x3AC0
    Supported Ids: 0203192102004000, 020C192102004000, 0203192102024000, 020C192102024000, 020C192102004100, 0203192102004100, 020C192102014100, 0203192102014100, 020C192102014000, 0203192102014000, 020C192102034000, 0203192102034000, 0203192102024100, 020C192102024100, 0203192102034100, 020C192102034100, 0203192102054100, 020C192102054100, 0203192102044100, 020C192102044100
    eBB5ProtocolType: NEW
    Secondary boot loaded.
    Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
    Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
    Storage2: 0000 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
    Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
    Storage4: 00EC 0030 - 0000 0321 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
    Suggested algorithm: XSR 1.6
    Loading CMT update server data
    Algorithm: RAP3Gv40_XSR17_alg.fg [XSR 1.6] version: 11.14.0 revision: 3.0 size: 0x91BD2
    Supported Ids: 0203192102004000, 020C192102004000, 0203192102024000, 020C192102024000, 020C192102004100, 0203192102004100, 020C192102014100, 0203192102014100, 020C192102014000, 0203192102014000, 020C192102034000, 0203192102034000, 0203192102024100, 020C192102024100, 0203192102034100, 020C192102034100, 0203192102054100, 020C192102054100, 0203192102044100, 020C192102044100
    Update server code loaded.
    Waiting for USB device removal ...
    Device connected: nmwcdnsuc\Nokia USB Flashing Generic, PORT_ID: 1386D557
    FUR: Adding Asic CMT as client OK.
    Reading CMT NPC (0x168 bytes).
    Reading CMT VARIANT (0x0 bytes).
    Reading CMT CCC (0x160 bytes).
    Reading CMT HWC (0xD4 bytes).
    Reading CMT R&D (0x0 bytes).
    Reading CMT MDM_KEYS (0x0 bytes).
    Reading CMT PARTNERC (0x0 bytes).
    RPL(CERT) backup already exist (C:\mobileEx\3.5\data\backup\BB5_35340204464505_CERT.rpl).
    CMT PAPUBKEYS HASH: 108AF4DB7EC8B1B36E9D6A60F7EB2996DC7B2B5D
    Storing certificate [NPC, CCC, HWC, R&D] ...OK
    Partitioning....
    Partitioning complete
    Erase size: 37.69 MB
    CMT FLASH,MuxOneNAND area [00020000-000203FF]
    CMT FLASH,MuxOneNAND area [00060000-0009FFFF]
    CMT FLASH,MuxOneNAND area [000A0000-0025FFFF]
    CMT FLASH,MuxOneNAND area [003E0000-005DFFFF]
    CMT FLASH,MuxOneNAND area [005E0000-010DFFFF]
    CMT FLASH,MuxOneNAND area [01EC0000-01EDFFFF]
    CMT FLASH,MuxOneNAND area [027C0000-02CBFFFF]
    CMT FLASH,MuxOneNAND area [077C0000-07B3FFFF]
    CMT FLASH,MuxOneNAND area [010E0000-01EBFFFF]
    Formating partition ...
    Flash programming ...
    CMT ADA block sent
    CMT KEYS block sent
    CMT PRIMAPP block sent
    CMT PASUBTOC block sent
    CMT PAPUBKEYS: 108AF4DB [RAP Certificate v1 236] sent
    CMT RAP3NAND block sent
    CMT UPDAPP block sent
    WriteDevice failed: Pokrywająca się operacja We/Wy jest w toku
    Error while programming [00] at 0x000E0400, Result: 0000
    Task failed at (0800001C)!!!
    Last RX buffer: 80 10 6F 00
  • Poziom 10  
    Nikt nie ma żadnego pomysłu? W między czasie zrobiłem klika sztuk sl3 i wszystko poszło jak po maśle, także jakąkolwiek wadę urządzeń czy kompa wykluczam. Kabel też kupiłem nowy i na pewno 6303ci (wiem że 6303 jest inny) Ratujcie bo ja już pomysłów nie mam...
  • Poziom 24  
    Wygląda na to jakby telefony miały uszkodzone certyfikaty. Infinity po usb z dead mode próbowałeś ? Spróbuj jeszcze inna wersje softu( wgraj jakąs z innym językiem a jak pójdzie ok to wtedy sobie tylko ppm wgrasz) i sprawdź dokładnie pliki czy napewno wszystko dajesz do 6303ci.
  • Poziom 27  
    A robieś downgrade jak ruszy to podnieś wrzuć polaka próbuj przez kopytko.

    Dodano po 8 [minuty]:

    Jeszcze jest opcja ruszyć go przez zasilacz serwisowy wejść w tryb local mode i spróbować flash.
  • Warunkowo odblokowany
    Możesz podpwoedzieć co z tym local mode ? Mam ten sam problem. Wiele telefonów przeflsahowałem, a na tym się wywalil i słuchawka martwa.
    Po fbus też nie chce flashowac.
  • Poziom 16  
    Mam ten sam problem 2 słuchawki mi sie wywaliły po probie wgrania flasha.
  • Warunkowo odblokowany
    U mnie pomogła zmiana kompa.