logo elektroda
logo elektroda
X
logo elektroda
REKLAMA
REKLAMA
Adblock/uBlockOrigin/AdGuard mogą powodować znikanie niektórych postów z powodu nowej reguły.

canon BJC50-migające diody

PiatyElement 16 Cze 2005 12:54 8007 15
REKLAMA
  • #1 1582313
    PiatyElement
    Poziom 21  
    witam, w czym problem??? canon bjc50 ruszy karetką kilka razy następnie zapiszczy 5razy i miga obydwoma diodami, głowica jest założona nowa, taśmę od głowicy do płyty prześwietliłem jest ok. proszę o jakieś sugestie. dzięki.
  • REKLAMA
  • #2 1582653
    Kazik
    Spec od drukarek
    W/g serwisówki masz przepełniony pampers. Cytat z serwisówki:

    1: Unplug Power Cord
    2: Hold POWER and RESUME buttons
    3: Plug in Power Cord
    4: Release buttons after the printers starts up
    5: Hold CARTRIDGE and RESUME
    6: Press POWER
    7: Release all buttons after the beeps
    8: Press CARTRIDGE 16 times
    9: Press RESUME
    10: Unplug the Power cord

    I powinien byc blad zresetowany.

    Nie musze chyba przypominac zeby zajrzec co tam sie dzieje z tym pampersem? ;)
  • #3 1582731
    PiatyElement
    Poziom 21  
    błąd BLINKS / BLINKS / 5 BEEP - Waste ink full dotyczy wg serwisówki canona BJC-80, natomiast w canonie bjc-50 pampers przepełniony ma inny kod błędu. W serwisówce do BJC-50 diody BLINKS / BLINKS / 1-12Beeps oznaczone sąjako: Service Errors.
  • #4 1583049
    bahet
    Poziom 23  
    To jest strona z BJC50

    canon BJC50-migające diody
  • REKLAMA
  • #5 1583224
    mags
    Poziom 13  
    Przeprowadz powyzszą procedure pomoze na 99,9 %

    Waste Error Reset

    1: Unplug Power Cord
    2: Hold POWER and RESUME buttons
    3: Plug in Power Cord
    4: Release buttons after the printers starts up
    5: Hold CARTRIDGE and RESUME
    6: Press POWER
    7: Release all buttons after the beeps
    8: Press CARTRIDGE 16 times
    9: Press RESUME
    10: Unplug the Power cord
  • REKLAMA
  • #6 1583919
    PiatyElement
    Poziom 21  
    niestety nie pomaga, w serwisówce do bjc50 opisane ( blink/blink/ 1-12beeps) opisane jest jako service error. nie mylcie tego z problemem pampersa bo to sie tyczy BJC80 wg serwisówki.
  • #7 1583948
    PiatyElement
    Poziom 21  
    no faktycznie z tej serwisówki wynika ze to problem pampersa ale ja mam inną ( jutro moge podać na nią namiary na www) z której wynika co innego. A jak ta drukarka sprawdza przepełnienie wkładu???? ma czujnik czy poprostu sobie przelicza???. wyjąłem wkład który owszem zalany jest tuszem po uszy, zrobiłemzalecany reset i ..... lipa.
  • #8 1584255
    mags
    Poziom 13  
    Zerknij na to :

    Error Codes
    Error Condition Error LED Power LED Beeps Solution
    Paper Pickup Steady Steady 1 Add paper or restack
    Paper Delivery Steady Steady 2 Remove any paper jammed
    BJ Cartridge Not Detected Steady Steady 3 Re-install cartridge or replace it
    Cartridge Mismatch Steady Steady 4 Install correct cartridge
    No Battery Steady Steady 6 Install battery
    Low Battery Warning Steady Steady Long / Short Charge battery
    Manual Feed Error Blinks Steady 1 Check paper
    Low Ink Blinks Steady 2 Replace cartridge
    Cartridge Error Blinks Steady 3 Check/Reinstall cartridge, replace cartridge
    Low Battery Warning Blinks Steady 4 Charge battery
    Waste Full Warning Blinks Steady 5 Waste is almost full , printer needs service
    Failed Battery Warning Blinks Steady 6 Replace battery
    Service Errors Blinks Blinks 1-12 Requires service

    If the printer does not turn on and the adapter is plugged in. There is a power lock switch at the side of the printer beside the power connector, insure this is not in the lock position. If the power lock is enabled when the printer is on, you will not be able to switch the printer off.

    Waste Error Reset

    1: Unplug Power Cord
    2: Hold POWER and RESUME buttons
    3: Plug in Power Cord
    4: Release buttons after the printers starts up
    5: Hold CARTRIDGE and RESUME
    6: Press POWER
    7: Release all buttons after the beeps
    8: Press CARTRIDGE 16 times
    9: Press RESUME
    10: Unplug the Power cord
  • REKLAMA
  • #9 1584610
    kosmita
    VIP Zasłużony dla elektroda
    offtopic: Zostały scalone dwa tematy

    pozdrawiam
  • #10 1585569
    PiatyElement
    Poziom 21  
    chyba mam pomroczność jasną ale ten reset nie dziala a chyba dobrze go robię????:
    1: Unplug Power Cord - wyciągnąć przewód zasilania
    2: Hold POWER and RESUME buttons - trzymać wciśnięte PWR i RESUME
    3: Plug in Power Cord - podpiąć przewód zasilania
    4: Release buttons after the printers starts up - zwolnić trzymane przyciski (PWR i RESUME)
    5: Hold CARTRIDGE and RESUME - wcisnąć i trzymać car... i resume
    6: Press POWER - wcisnąć power
    7: Release all buttons after the beeps - zwolnić po usłyszeniu pisków car.. i resume
    8: Press CARTRIDGE 16 times - nacisnąć 16 razy cartridge
    9: Press RESUME - nacisnąć resume
    10: Unplug the Power cord - wypiąć przewód zasilania.

    uuff... i .....lipa no chyba ze coś źle robię
    bateria ma być wyjęta rozumem.
  • #11 1600871
    PiatyElement
    Poziom 21  
    witam ponownie czy słyszał ktoś o jakimś sofcie do wgrywania do drukarki oprogramowania???? bo podobno takowy istnieje.
  • #12 2697782
    lord wiader
    Poziom 15  
    Witam
    Wiem że to stary temat ale może komuś się przyda jak kasować pampersa.Bateria faktycznie ma być wyciągnięta głowica też ale przewód zasilający wsunięty do gniazda zasilania i postępować zgodnie z powyższymi instrukcjami opisanych przez innych.Z tą różnicą że przewodu się nie wkłada tylko przesówa suwak blokady panelu sterowania nad gniazdem zasilania.

    Pozdrawiam.
  • #13 2914504
    Piotr76
    Poziom 11  
    Witam,
    Mam ten sam problem tj po wlaczeiu bjc-50 nastepuje czyszczenie glowicy zaraz potem pojawia sie 5 sygnalow i drukarka zaczyna mrugac diodami error(pomaranczowy) i power(zielony kolor). Reset pampersa nie pomaga i z pewnoscia nie o niego tu chodzi. Jezeli ktos mial podobny przypadek prosze o rade. Mam takie dwie sztuki i powoli zaczynam sie poddawac. Pozdrawiam! :roll: :roll: :roll:
  • #14 5787623
    zenio45
    Poziom 1  
    mam ten sam problem z canon bjc 50 migajaca dioda cardrige
  • #15 6466153
    janusz2k
    Poziom 15  
    Nie wiem, czy nie ma błędu w opisie procedury Reset Waste..., w każdym razie wykonałem tę procedurę, ale w punkcie 2 zamiast [hold Power and Resume] trzymałem tylko RESUME, reszta jak w opisie i chyba zadziałało.
  • #16 8034039
    cidik
    Poziom 2  
    Problems with Cartridge Detection

    * Power off the printer
    * Unplug the printer's power cord, wait 5 seconds then replug the power cord in.
    * Hold the Power button for 6 Beeps
    * Release the Power Button

    This will reset the printer and should resolve incorrect cartridge detection problems.


    To pomoże jak wam mruga cały czas dioda... Pozdrawaiam
REKLAMA