Elektroda.pl
Elektroda.pl
X

Search our partners

Find the latest content on electronic components. Datasheets.com
Elektroda.pl
Please add exception to AdBlock for elektroda.pl.
If you watch the ads, you support portal and users.

Brak nawiewu pasażerów Chrysler Grand Voyager 3.3 benzyna 2001

michalfans 25 Nov 2021 10:59 54 5
  • #1
    michalfans
    Level 8  
    Witam. Posiadam Chrysler Grand Voyager 3.3 2001rok. Mam problem z nawiewem, działa tylko na podszybiu, a gdy zmieniam na nogi lub pasażerów to dalej jest tylko na szyby. Co to może być za problem, pomocy. Dziękuję z góry. Brak nawiewu pasażerów Chrysler Grand Voyager 3.3 benzyna 2001
    Kamery 3D Time of Flight - zastosowania w przemyśle. Darmowe szkolenie 16.12.2021r. g. 10.00 Zarejestruj się
  • #2
    sanfran
    Level 40  
    Pokrętło napędza rolkę z krzywdami, które z kolei są połączone z klapkami otwierającymi lub zamykającymi nawiewy.
    Należy delikatnie ściągnąć przedni panel i zobaczyć czy coś się nie odłączyło lub ułamało.
  • #3
    michalfans
    Level 8  
    To pokrętło jest elektroniczne
  • #5
    michalfans
    Level 8  
    Ok, tylko nigdzie nie mogę znaleść jak zrobić taką kalibrację. Co po kolei trzeba zrobić?
  • #6
    cyborg39
    Level 27  
    "HEATER-A/C CONTROL CALIBRATION The heater-A/C control module must be recalibrated each time an actuator motor or the control module is replaced. If the vehicle is so equipped, the calibration procedure also includes rear HVAC positions for each actuator motor. 1. Turn the ignition switch to the On position. Simultaneously depress and hold the Power and Recirculation buttons on the heater-A/C control for at least five seconds. 2. The manual heater-A/C control power Light Emitting Diode (LED) and Recirculation LED, or the Automatic Temperature Control (ATC) heater-A/C control Delay and Recirculation graphics will begin to flash when the calibration procedure has begun. 3. The calibration procedure should take less than two minutes to complete for the manual heater- A/C control, and less than twenty seconds for the ATC heater-A/C control. When the LEDs or graphics stop flashing, the calibration procedure is complete. 4. If the LEDs or graphics continue to flash beyond the normal three minute (manual) or twenty second (ATC) calibration time, it indicates that the heater-A/C control has detected a failure and a Diagnostic Trouble Code (DTC) has been set. 5. Use a DRBIII scan tool to perform further diagnosis. Refer to the appropriate diagnostic information. The LEDs or graphics will continue to flash even after the ignition switch is cycled Off and On, until a successful calibration is completed or until the vehicle has been driven about 8 miles."

    Drugi opis:
    The ambient air temperature in the room where
    the vehicle will be tested must be a minimum of 21°
    C (70°F) for this test. The test is activated by
    depressing the A/C and PWR buttons simultaneously
    and holding them depressed for no less than four seconds.
    The snowflake icon and the DELAY text in the
    ATC display will blink on and off alternately until
    the test is complete. If the snowflake icon and the
    DELAY text stop blinking before two minutes, then
    the cool down test has been completed successfully. If
    the two minutes expire without the evaporator temperature
    reaching 20° F less than the evaporator initial
    temperature, then the cool down test has been
    failed and further A/C system diagnosis is required.
    If the test is failed, the snowflake icon and the
    DELAY text will continue to blink across ignition
    cycles until the vehicle has been driven for greater
    than (8 miles).