logo elektroda
logo elektroda
X
logo elektroda
REKLAMA
REKLAMA
Adblock/uBlockOrigin/AdGuard mogą powodować znikanie niektórych postów z powodu nowej reguły.

Instrukcja inst gaz Koltec / necam

maras77 28 Lut 2007 01:54 13591 2
REKLAMA
  • #1 3626303
    maras77
    Poziom 21  
    Po angielsku ze strony:
    http://www.askanowner.nl/qa/view.asp?guid=&sid=2&qid=236439
    http://www.askanowner.com/_upload/1_2/attachm...ad%20out%20Diagnostic%20system%20Koltec_2.pdf

    Jest to cenna wiedza, bo na naszym forum koleś chciał ode mnie 100 zł za tą instrukcję.
    Ostatnie zdania to rozwiązanie częstego problemu pt przełącza się sam na benzynę ;)

    Więc czytać:

    Read out diagnostic system for Koltec EGI / GSI.
    De EGI LPG installation from Koltec has a self diagnostic-system which all disturbances will
    be storages in its memory for a time.
    When you have a problem whit the LPG installation, the first you have to do is read out this
    memory.
    This prevents expensive repairs, because the most auto mechanicals don’t have knowledge for
    LPG installations.
    Read out this memory is not difficult, and you don’t need expensive tools.
    Behind de switch for choosing LPG / petrol is a grey wire whit a connector which is not
    connected.
    This wire has to be extended whit a other wire and connected whit the earth (chassis) of the
    car.
    Then you turn on the car key till all light bulbs in the dashboard go on all but don’t start the
    engine.
    The light bulb in the LPG/petrol switch goes flashing now.
    This flashing is the giving the disturbances if there are.
    Example1: 1x flashing, waiting a moment and then 2x flashing behind each other is code 12 =
    no turning signal for the engine.
    Note: This code is correct because we didn’t start the engine.(just at older types > 1995)
    Example2: 4x flashing, waiting a moment and then 5x flashing behind each other is code 45 =
    Gas mixture to rich.
    Note: this code is coming often if the Vaporiser needs revision.
    The diaphragms leaking and the Vaporiser/ pressure regulator don’t working well.
    Every code will be given 3 times after each other before given a next code.
    Codes which can be given:
    Code 12 No turning signal for the engine (Vaporiser whitout temperature sensor)
    (older type >1995)
    Code 13 No Lambda sondesignal (lambdasonde or wiring is damaged)
    Code 14 Temperature sensor signal to high.
    (Vaporiser whit temperature sensor)(newer type 1995>)
    Code 15 Temperature sensor signal to low.
    (Vaporiser whit temperature sensor)(newer type 1995>)
    Code 21 TPS-signal to high.(TPS = Throttle Position Sensor)
    Code 22 TPS-signal to low.
    Code 33 MAP-sensor signal to high.
    Code 34 MAP-sensor signal to low.
    Code 43 Divider/regulator don’t working.
    Code 45 Gas mixture to rich.(light bulb in switch is flashing by driving the car)
    When the gas mixture is to poor, the diagnose system gives no signal because it is thinking
    the tank is (almost) empty.(light bulb in switch is flashing by driving the car)
    If this is this is take a longer time, the system goes automatically to petrol run.
    If the system is giving no disturbance code, and the light bulb in the switch doesn’t flash by
    driving the car, the pressures don’t need to be checked
  • REKLAMA
  • #2 5500814
    Krzysiekfx
    Poziom 11  
    Witam kolego jeżeli instalacja przełącza z lpg na bp to masz zatkaną instalację brudem
  • #3 10468831
    kubiec1
    Poziom 14  
    maras77 napisał:
    Po angielsku ze strony ..... Jest to cenna wiedza

    Potwierdzam, że wiadomości podane w poście przydadzą się każdemu.
    Dla tych, którzy nie znają angielskiego zamieszczam link do polskich porad dot. Koltec Necam www.koltec.implesite.pl
REKLAMA