[ 0.000000] Linux version 2.6.26 (hahihe@swfarm-l3) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #108 PREEMPT Fri Jun 5 09:27:39 KST 2009
[ 0.000000] LINUX started...
[ 0.000000] console [early0] enabled
[ 0.000000] CPU revision is: 0001906c (MIPS 4KEc)
[ 0.000000] Begin Titania_setup
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 008bf000 @ 003ff000 <7>(reserved)
[ 0.000000] memory: 00301000 @ 008bf000 <7>(usable)
[ 0.000000] memory: 02f00000 @ 04200000 <7>(usable)
[ 0.000000] Wasting 71648 bytes for tracking 2239 unused pages
[ 0.000000] Entering add_active_range(0, 1023, 3262) 0 entries of 256 used
[ 0.000000] Entering add_active_range(0, 2239, 3008) 1 entries of 256 used
[ 0.000000] Entering add_active_range(0, 16896, 28928) 1 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 1023 -> 28928
[ 0.000000] Normal 28928 -> 28928
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0 1023 -> 3262
[ 0.000000] 0 16896 -> 28928
[ 0.000000] On node 0 totalpages: 14271
[ 0.000000] DMA zone: 219 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 14052 pages, LIFO batch:3
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 14052
[ 0.000000] Kernel command line: root=/dev/mtdblock3 rootfstype=squashfs lpj=105984 host=saturn6 noinitrd ramdisk=0 console=ttyS0,115200n8r ip=156.147.69.181:192.168.0.1:192.168.0.10:192.168.0.1:255.255.255.0 xipfs=15 fontxipfs=0 quiet_app loglevel=0 memsize=128
[ 0.000000] Primary instruction cache 4kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[ 0.000000] CPU freq count = 108000000
[ 0.000000] CPU frequency 216.00 MHz
[ 0.000000] console handover: boot [early0] -> real [ttyS0]
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.001000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.018000] Memory: 50164k/51204k available (2421k kernel code, 984k reserved, 1757k data, 112k init, 0k highmem)
[ 0.018000] SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.019000] Calibrating delay loop (skipped)... 211.96 BogoMIPS preset
[ 0.019000] Mount-cache hash table entries: 512
[ 0.040000] net_namespace: 192 bytes
[ 0.041000] NET: Registered protocol family 16
[ 0.076000] SCSI subsystem initialized
[ 0.079000] usbcore: registered new interface driver usbfs
[ 0.082000] usbcore: registered new interface driver hub
[ 0.084000] usbcore: registered new device driver usb
[ 0.100000] BOOTSTRAP 13(2)
[ 0.102000] NET: Registered protocol family 2
[ 0.111000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.114000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.115000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.115000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.115000] TCP reno registered
[ 0.118000] NET: Registered protocol family 1
[ 0.202000] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[ 0.206000] NTFS driver 2.1.29 [Flags: R/O].
[ 0.211000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.219000] msgmni has been set to 98
[ 0.222000] io scheduler noop registered (default)
[ 0.225000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.230000] serial8250: ttyS0 at I/O 0xbf801300 (irq = 8) is a 16550
[ 0.259000] loop: module loaded
[ 0.260000] Driver 'sd' needs updating - please use bus_type methods
[ 0.265000] NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
[ 0.265000] Loading nand bad block info...
[ 0.266000] Loading nand bad block info(00000000+00004000)...
[ 0.269000] nand_bbm_info_load: Loading nand bad block info...ok
[ 0.269000] nand bad block information:
[ 0.269000] magic = 0x8192a5a6
[ 0.269000] bad block count = 2
[ 0.269000] assign index = 4093
[ 0.269000] 00000e5d -> 00000fff
[ 0.269000] 00000e5e -> 00000ffe
[ 0.269000] Mstar nand-flash partition definition
[ 0.270000] mtd info : # of partition = 19
[ 0.270000] Creating 19 MTD partitions on "NAND 64MiB 3,3V 8-bit":
[ 0.270000] 0x00000000-0x00020000 : "bbminfo"
[ 0.278000] 0x00020000-0x00060000 : "boot"
[ 0.283000] 0x00080000-0x000a0000 : "mtdinfo"
[ 0.289000] 0x000a0000-0x00220000 : "rootfs"
[ 0.295000] 0x00220000-0x00240000 : "model"
[ 0.301000] 0x00240000-0x00740000 : "emanual"
[ 0.306000] 0x00740000-0x00b40000 : "ezcal"
[ 0.312000] 0x00b40000-0x00dc0000 : "kernel"
[ 0.318000] 0x00dc0000-0x016c0000 : "lgapp"
[ 0.323000] 0x016c0000-0x01a40000 : "lgres"
[ 0.329000] 0x01a40000-0x02340000 : "lgfont"
[ 0.335000] 0x02340000-0x025c0000 : "kernel"
[ 0.341000] 0x025c0000-0x02ec0000 : "lgapp"
[ 0.346000] 0x02ec0000-0x03240000 : "lgres"
[ 0.352000] 0x03240000-0x03b40000 : "lgfont"
[ 0.358000] 0x03b40000-0x03b60000 : "recdb"
[ 0.364000] 0x03b60000-0x03ba0000 : "system"
[ 0.369000] 0x03ba0000-0x03e00000 : "user"
[ 0.375000] 0x03e00000-0x04000000 : "reserved"
[ 0.381000] Disable power down for H.264 firmware
[ 0.381000] GE driver inits
[ 0.381000] GOP driver inits
[ 0.381000] GPIO Init(LCD)
[ 0.389000] [SCALER][000132] _mod_scaler_init
[ 0.389000] [MADMOD][002762] _mod_mad_init is invoked
[ 0.389000] init 160
[ 0.389000] [MVDMOD][000610] H264 bit-stream buffer addr 0xa9c00000; size 4194304
[ 0.389000] CI driver inits
[ 0.389000] [RLDMOD][000430] mod_rld_init is invoked
[ 0.389000] [RLDMOD][000434] call register_chrdev_region
[ 0.390000] [RLDMOD][000463] Init RLD successfully
[ 0.390000] [TTX_DRV][00559]init 170
[ 0.390000] [VE_DRV][00469]MDrv_VE_Module_Init is invoked
[ 0.390000] [VE_DRV][00473]call register_chrdev_region
[ 0.390000] [VE_DRV][00499]Init VE successfully
[ 0.390000] MDrv_CC_Init
[ 0.390000] init 172
[ 0.390000] <MHal_JPD_Initialize>
[ 0.390000] BT_USB initialized
[ 0.390000] Hello~ this is kernel module on MIPS MSB
[ 0.391000] BT_USB for INSTANT_INTERRUPT scheme rev2
[ 0.391000] SCHED: init_sched
[ 0.391000] bt_usb: Bluetooth USB driver for LGE DTV
[ 0.392000] usbcore: registered new interface driver csr_usb
[ 0.392000] bt_usb: BT USB driver registered
[ 0.392000] BlueCore transport started... May
[ 0.399000] TCP cubic registered
[ 0.399000] NET: Registered protocol family 17
[ 0.403000] Adding user_initcall[0] = 0x80581360
[ 0.403000] Adding user_initcall[1] = 0x80581340
[ 0.403000] Adding user_initcall[2] = 0x805845c4
[ 0.409000] VFS: Mounted root (squashfs filesystem) readonly.
[ 0.411000] Freeing unused kernel memory: 112k freed
[ 0.739000] CLEANMARKER node found at 0x00000000 has totlen 0xc != normal 0x0
[ 0.916000] cramfs: checking physical address 0x7100000 for linear cramfs image
[ 0.916000] cramfs: linear cramfs image appears to be 14344 KB in size
[ 1.301000] [SYS][000124] MDrv_SYS_SetPanelInfo
[ 1.331000] [MADMOD][002139] _mod_mad_open is invoked
[ 1.334000] [MADMOD][002241] ioctl: receive MDrv_MAD_INITIALIZE_MODULE ...
[ 1.459000] MDrv_MAD_Se_SetMemInfo: DSPMadBaseBufferAdr[DSP_SE] = 0x00C00000
[ 1.459000]
MDrv_MAD_ISRInit(101)...
[ 1.571000] MDrv_MAD_SoundEffectOnOff(1)...
[ 1.868000] TSP FW=0xbc0000
[ 1.886000] [SCALER][000180] _mod_scaler_open
[ 1.926000] [47;34m[HDMI][01461] ========enInputPortType==========0
[ 1.926000] [0mMHal_HDCP_InitProductionKey 50 d6 af 66 a1
[ 1.956000] COLOR KILL BOUND: 08 08
[ 1.957000] [VE_DRV][00313]MDrv_VE_Open is invoked
[ 1.957000] _MDrv_VE_TransferInputMux
[ 1.959000] [SYS][000124] MDrv_SYS_SetPanelInfo
[ 1.961000] GE opens successfully
[ 1.961000] GOP opens successfully
[ 2.035000] GwinID 3 used
[ 2.575000] GwinID 5 used
[ 3.778000] MDrv_MAD_DVB_PcmLevelControl:0
[ 4.676000] H.264 firmware version 0x1080353
[ 4.676000] [MVDMOD][000523] ioctl: H264 set data memory : 0x1e80000
[ 4.677000] [MVDMOD][000375] ioctl: H264 toggle AV sync: 1 : 1(E) 0(D)
[ 4.677000] Send CMD 0x100 to H264
[ 4.677000] [MVDMOD][000531] ioctl: H264 set delay time(ms): 18900
[ 4.677000] Send argument 0x49d4 to H264
[ 4.677000] [MVDMOD][000260] ioctl: H264 play mode: 0
[ 4.677000] Send CMD 0x100 to H264
[ 4.677000] Send CMD 0x18 to H264
[ 4.677000] Send argument 0x61a800 to H264
[ 4.677000] Send CMD 0x2c to H264
[ 4.678000] Send CMD 0x0 to H264
[ 4.678000] [MVDMOD][000381] ioctl: H264 Register interrupt
[ 4.680000] [MVDMOD][000409] ioctl: H264 set Interrupt flag b
[ 4.864000] MDrv_MAD_DVB_PcmLevelControl:1
[ 5.590000] [MVDMOD][000328] ioctl: H264 set vop done
[ 5.618000] H264 interrupt Fail to write MMAP [SEQ]
[ 5.618000] [MVDMOD][000328] ioctl: H264 set vop done
[ 7.918000] calling user_initcall 0x80581360
[ 7.918000] Second-Mstar-soc-ehci H.W init
[ 7.928000] Second-Mstar-soc-ehci Second-Mstar-soc-eh: Mstar EHCI
[ 7.936000] _MDrv_VE_SwitchInputSrc 0
[ 7.943000] Second-Mstar-soc-ehci Second-Mstar-soc-eh: new USB bus registered, assigned bus number 1
[ 7.943000] Second-Mstar-soc-ehci Second-Mstar-soc-eh: irq 42, io mem 0xbf801a00
[ 7.956000] usb usb1: configuration #1 chosen from 1 choice
[ 7.965000] hub 1-0:1.0: USB hub found
[ 7.966000] hub 1-0:1.0: 1 port detected
[ 8.079000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.079000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.079000] usb usb1: Product: Mstar EHCI
[ 8.079000] usb usb1: Manufacturer: Linux 2.6.26 ehci_hcd
[ 8.079000] usb usb1: SerialNumber: mstar
[ 8.086000] calling user_initcall 0x80581340
[ 8.087000] Mstar-soc-ehci H.W init
[ 8.097000] Mstar-soc-ehci Mstar-soc-ehci.0: Mstar EHCI
[ 8.105000] Mstar-soc-ehci Mstar-soc-ehci.0: new USB bus registered, assigned bus number 2
[ 8.106000] Mstar-soc-ehci Mstar-soc-ehci.0: irq 15, io mem 0xbf804800
[ 8.120000] usb usb2: configuration #1 chosen from 1 choice
[ 8.127000] hub 2-0:1.0: USB hub found
[ 8.127000] hub 2-0:1.0: 1 port detected
[ 8.240000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.240000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.240000] usb usb2: Product: Mstar EHCI
[ 8.240000] usb usb2: Manufacturer: Linux 2.6.26 ehci_hcd
[ 8.241000] usb usb2: SerialNumber: mstar
[ 8.243000] calling user_initcall 0x805845c4
[ 8.243000] Initializing USB Mass Storage driver...
[ 8.246000] usbcore: registered new interface driver usb-storage
[ 8.246000] USB Mass Storage support registered.
[ 150.241000] Plug in USB Port1
[ 150.588000] usb 2-1: configuration #1 chosen from 1 choice
[ 150.602000] scsi0 : SCSI emulation for USB Mass Storage devices
[ 150.606000] usb-storage: device found at 2
[ 150.606000] usb-storage: waiting for device to settle before scanning
[ 150.624000] scsi 0:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0 CCS
[ 150.633000] usb 2-1: New USB device found, idVendor=0bda, idProduct=0116
[ 150.633000] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 150.633000] usb 2-1: Product: USB2.0-CRW
[ 150.633000] usb 2-1: Manufacturer: Generic
[ 150.633000] usb 2-1: SerialNumber: 20021111153705700
[ 151.266000] sd 0:0:0:0: [sda] 3911680 512-byte hardware sectors (2003 MB)
[ 151.269000] sd 0:0:0:0: [sda] Write Protect is off
[ 151.271000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 151.271000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 151.284000] sd 0:0:0:0: [sda] 3911680 512-byte hardware sectors (2003 MB)
[ 151.289000] sd 0:0:0:0: [sda] Write Protect is off
[ 151.289000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 151.289000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 151.290000] sda: sda1
[ 151.304000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 151.310000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 151.325000] usb-storage: device scan complete
[ 155.866000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
