witam mam taki problem posiadam programator prodigy podłanczam fona do prodigy na lcd widnieje napis NOKIA na dole teraz malutkie mytanko posiadam program prodigy plus jak go fleshowac bo nie odpala normalnie nie wina tasmy bankowo dalem nowa hot airem zrobilem bo wogóle nie reagowal na boxa teraz wygrzalem ladnie plytke i jets luz ale co dalej moze mi ktos pomuc w tej sprawie
Dodano po 9 [minuty]:
jak robie test mam tak
ST_UPP_REGISTER_VER_TEST - PASSED
ST_UEM_CBUS_IF_TEST - PASSED
ST_SLEEP_X_LOOP_TEST - PASSED
ST_AUX_DA_LOOP_TEST - PASSED
ST_EAR_DATA_LOOP_TEST - PASSED
ST_TX_IDP_LOOP_TEST - PASSED
ST_TX_IQ_DP_LOOP_TEST - PASSED
ST_SIM_CLK_LOOP_TEST - PASSED
ST_SIM_IO_CTRL_LOOP_TEST - PASSED
ST_MBUS_RX_TX_LOOP_TEST - PASSED
ST_BACKUP_BATT_TEST - PASSED
ST_PA_TEMP_TEST - PASSED
ST_KEYBOARD_STUCK_TEST - PASSED
ST_LCD_TEST - PASSED
ST_LPRF_IF_TEST - PASSED
ST_CURRENT_CONS_TEST - FAILED
ST_CAMERA_IF_TEST - FAILED
ST_EXTERNAL_RAM_TEST - PASSED
ST_IR_IF_TEST - PASSED
ST_AEM_CBUS_IF_TEST - PASSED
ST_PROX_FAULT_TEST - PASSED
ST_VIBRA_TEST - FAILED
ST_KEYB_LINE_TEST - PASSED
ST_RF_CHIP_ID_TEST - PASSED
Dodano po 41 [minuty]:
oki poradzilem se chyba niewiem trwało to troche ale czy wgral go czy tez nie??
pisze teraz tak
w programie
EPOC BT Flash Enabled...
MCU flashing - NHL23250.6C1
Init flashing...
Boot 1 Ok.. ,UPP_WD2 v2.0, 2.01, 2.1
Boot 2 Ok..
FlashID0: 00EC22F0, Sams K5U28818TM;128Mb
Sending Algorithm...
Success. Performing Authentification...
MSID: 84E0F4CBB4B9AB5CF4C007D5CC
Uem ID:00098A80
Erasing MCU area...
Area: 00000000-0000FFFF - Erasing...
Area: 00010000-00EF9FFF - Erasing...
Area: 00FF0000-00FFC000 - Erasing...
MCU area erased.
Writing MCU file...
Mcu flashing took: 6 min 11 sec
PPM flashing - NHL23250.616
Erasing PPM area...
Area: 00000000-0000FFFF - Erasing...
Area: 00F00000-00FBDFFF - Erasing...
PPM area erased.
Writing PPM file...
Success.
PPM flashing took: 18 sec
Total time: 6 min 29 sec
Polling product, Please wait...
Unable to detect connected product!, Will skip upload
All Done.
Dodano po 9 [minuty]:
jak robie test mam tak
ST_UPP_REGISTER_VER_TEST - PASSED
ST_UEM_CBUS_IF_TEST - PASSED
ST_SLEEP_X_LOOP_TEST - PASSED
ST_AUX_DA_LOOP_TEST - PASSED
ST_EAR_DATA_LOOP_TEST - PASSED
ST_TX_IDP_LOOP_TEST - PASSED
ST_TX_IQ_DP_LOOP_TEST - PASSED
ST_SIM_CLK_LOOP_TEST - PASSED
ST_SIM_IO_CTRL_LOOP_TEST - PASSED
ST_MBUS_RX_TX_LOOP_TEST - PASSED
ST_BACKUP_BATT_TEST - PASSED
ST_PA_TEMP_TEST - PASSED
ST_KEYBOARD_STUCK_TEST - PASSED
ST_LCD_TEST - PASSED
ST_LPRF_IF_TEST - PASSED
ST_CURRENT_CONS_TEST - FAILED
ST_CAMERA_IF_TEST - FAILED
ST_EXTERNAL_RAM_TEST - PASSED
ST_IR_IF_TEST - PASSED
ST_AEM_CBUS_IF_TEST - PASSED
ST_PROX_FAULT_TEST - PASSED
ST_VIBRA_TEST - FAILED
ST_KEYB_LINE_TEST - PASSED
ST_RF_CHIP_ID_TEST - PASSED
Dodano po 41 [minuty]:
oki poradzilem se chyba niewiem trwało to troche ale czy wgral go czy tez nie??
pisze teraz tak
w programie
EPOC BT Flash Enabled...
MCU flashing - NHL23250.6C1
Init flashing...
Boot 1 Ok.. ,UPP_WD2 v2.0, 2.01, 2.1
Boot 2 Ok..
FlashID0: 00EC22F0, Sams K5U28818TM;128Mb
Sending Algorithm...
Success. Performing Authentification...
MSID: 84E0F4CBB4B9AB5CF4C007D5CC
Uem ID:00098A80
Erasing MCU area...
Area: 00000000-0000FFFF - Erasing...
Area: 00010000-00EF9FFF - Erasing...
Area: 00FF0000-00FFC000 - Erasing...
MCU area erased.
Writing MCU file...
Mcu flashing took: 6 min 11 sec
PPM flashing - NHL23250.616
Erasing PPM area...
Area: 00000000-0000FFFF - Erasing...
Area: 00F00000-00FBDFFF - Erasing...
PPM area erased.
Writing PPM file...
Success.
PPM flashing took: 18 sec
Total time: 6 min 29 sec
Polling product, Please wait...
Unable to detect connected product!, Will skip upload
All Done.
